欢迎访问《电化学(中英文)》期刊官方网站,今天是

电化学(中英文) ›› 2021, Vol. 27 ›› Issue (5): 579-585.  doi: 10.13208/j.electrochem.201026

• 论文 • 上一篇    下一篇

流道与肋宽比对气体扩散层性能影响的数值研究

魏荣强1, 李世安1,2,*(), 刘艺辉1, 杨治1, 沈秋婉1,2, 杨国刚1,2   

  1. 1.大连海事大学轮机工程学院,辽宁 大连 116026
    2.大连海事大学新能源船舶动力技术研究院,辽宁 大连 116026
  • 收稿日期:2020-10-14 修回日期:2021-02-18 出版日期:2021-10-28 发布日期:2021-02-22
  • 通讯作者: 李世安 E-mail:lishian@dlmu.edu.cn
  • 基金资助:
    国家自然科学基金(51779025);国家自然科学基金(52001045);中国博士后基金(2019M651097);中国博士后基金(2019M651094);辽宁省自然科学基金(2019-BS-026);辽宁省自然科学基金(2020-HYLH-38)

Numerical Study on the Influences of Flow Channel and Rib Width Ratio on the Performance of Gas Diffusion Layer

Rong-Qiang Wei1, Shi-An Li1,2,*(), Yi-Hui Liu1, Zhi Yang1, Qiu-Wan Shen1,2, Guo-Gang Yang1,2   

  1. 1. School of Marine Engineering, Dalian Maritime University, Dalian 116026, Liaoning, China
    2. The Institute of New Energy Technologies for Ship Power System, Dalian Maritime University,Dalian 116026, Liaoning, China
  • Received:2020-10-14 Revised:2021-02-18 Published:2021-10-28 Online:2021-02-22
  • Contact: Shi-An Li E-mail:lishian@dlmu.edu.cn

摘要:

由于装配压力的作用,气体扩散层产生形变,对质子交换膜燃料电池性能产生影响。国内外学者主要研究气体扩散层形变后对燃料电池性能产生的影响,但对不同流道宽度的燃料电池探究尚不明确。本文采用有限元法建立一个单流道质子交换膜燃料电池三维模型,研究了不同装配压力以及三种流道与肋度比(流道与肋宽比分别为3:2、1:1、2:3)下,气体扩散层厚度变化规律以及它们对孔隙率和电导率的影响。结果显示,随着装配压力的增加,肋下气体扩散层厚度变薄,孔隙率减小,电导率增加;在相同装配压力下,流道与肋宽度比值越大,肋下孔隙率越小,电导率越大。

关键词: 气体扩散层, 装配压力, 质子交换膜燃料电池, 性能

Abstract:

Proton exchange membrane fuel cell (PEMFC) has the advantages of low noise, high power density, and zero emission. It is widely used in ships, automobiles, aviation and other fields. PEMFC is composed of bipolar plate (BP), gas diffusion layer (GDL), catalytic layer (CL) and proton exchange membrane (PEM). GDL has a supporting catalytic layer and proton exchange membrane, which provides gas diffusion for the reaction and a channel for the reaction to produce water, and transmits the anodic oxidation reaction. In the assembly of fuel cells, a certain assembly pressure is required to ensure air-tightness and effective conductivity. The assembly pressure will cause the GDL deformation and the loss of hydrophobic materials; however, the assembly pressure can improve the durability of the battery. Too small assembly pressure will lead to insufficient battery sealing, high contact resistance and other undesirable results. Larger assembly pressure can improve the hydrogen utilization rate and ensure the stable operation of the battery as the assembly pressure increases, Liquid water accumulates more; excessive assembly pressure leads to reduced porosity and lower reaction rate, and even damage of membrane electrode assembly (MEA). Therefore, there is an optimal assembly pressure to obtain lower contact resistance when compressing GDL. At the same time, it has a relatively high porosity. Scholars at home and abroad have mainly studied the effect of GDL deformation on the battery performance, but the exploration of fuel cells with different flow channel widths is not clear. This paper uses the finite element method to establish a single flow. Three-dimensional model of the PEMFC channel has been studied, and the GDL thickness changes and their impacts on the pores under different assembly pressures and three kinds of flow channel to rib ratios (the channel and rib width ratios of 3:2, 1:1, 2:3) were investigated. The results show that: (1) GDL deformation increased with the increases of the ratio of flow channel to rib width and assembly pressure, but the rate of change gradually slowed down. (2) Under the ribs,the porosity of GDL decreased with the increase of assembly pressure, and the decreased change rate continued to be accelerated; under the same assembly pressure, the greater the ratio of channel to rib width, the more significant the porosity change. (3) Conductivity increased with the increase of assembly pressure, and the rate of change was also accelerated with the increase of assembly pressure; under the same assembly pressure, the greater the ratio of the flow channel to the rib width, the greater the electrical conductivity. When the ratio of channel to rib width was 3:2, there was an intersection point at 1.5 ~ 2.0 MPa. According to the balanced relationship between porosity and conductivity, the optimal assembly pressure may be in this interval, which needs to be further verified.

Key words: gas diffusion layer, assembly pressure, proton exchange membrane fuel cell, performance