欢迎访问《电化学(中英文)》期刊官方网站,今天是

电化学(中英文) ›› 2023, Vol. 29 ›› Issue (8): 2209231.  doi: 10.13208/j.electrochem.2209231

所属专题: “电子电镀和腐蚀”专题文章

• 论文 • 上一篇    下一篇

应用于大马士革工艺的纳米孪晶铜脉冲电沉积研究

王玉玺a,b, 高丽茵a,*(), 万永强a, 李哲a, 刘志权a,b,*()   

  1. a中国科学院深圳先进技术研究院,深圳先进电子材料国际创新研究院,广东 深圳 518055
    b中国科学技术大学纳米科学技术学院,江苏 苏州 215213
  • 收稿日期:2022-09-23 修回日期:2022-11-23 接受日期:2022-12-02 出版日期:2023-08-28 发布日期:2022-12-08

Pulse Electroplating of Nanotwinned Copper Using MPS-PEG Two-Additive System for Damascene via Filling Process

Yu-Xi Wanga,b, Li-Yin Gaoa,*(), Yong-Qiang Wana, Zhe Lia, Zhi-Quan Liua,b,*()   

  1. aShenzhen Institute of Advanced Electronic Materials, Shenzhen Institute of Advanced Technology, Chinese Academy of Sciences, Shenzhen 518055, China
    bNano Science and Technology Institute, University of Science and Technology of China, Suzhou 215213, China
  • Received:2022-09-23 Revised:2022-11-23 Accepted:2022-12-02 Published:2023-08-28 Online:2022-12-08
  • Contact: *Tel: (86)13555867395; E-mail: ly.gao@siat.ac.cn; Tel: (86)18624083161; E-mail: zqliu@siat.ac.cn

摘要:

本文在前期优化的电镀液的基础上,使用脉冲电镀工艺获得了高密度的纳米孪晶铜。为了进一步揭示孪晶形成的影响因素,研究了系列MPS浓度在镀液中的作用。当镀液中并未添加MPS时,镀层由粗大的晶粒组成,平均晶粒大小为0.9 μm,晶粒内部含有少量的垂直或倾斜于膜面的孪晶界,镀层的晶粒取向为(110)和(111)共存,两者织构比例分别为49%和27.8%。从FIB微观组织观察和X射线衍射的结果可知,当镀液中添加10 ppm的MPS后,镀层组织变为柱状纳米孪晶铜组织,柱状晶内部含有高密度水平方向的孪晶界,同时晶粒取向变为高度择优的(111)。当MPS含量从10 ppm持续上升至40 ppm,镀层组织和晶粒取向无明显变化。具体地,当镀液中添加40 ppm的MPS时,镀层晶粒大小为0.6 μm,且镀层晶粒(110)和(111)的织构比例分别为3.45%和95.1%。这说明,可以通过MPS的含量调节提高纳米孪晶铜电镀液的填充能力,而纳米孪晶微观组织的形成并不受影响。基于上述结果,我们使用该电镀液配方及工艺进行了大马士革微盲孔的填充。结果表明,当MPS含量为40 ppm时,可以实现大马士革微盲孔的无孔填充。纳米孪晶铜电镀液填充能力的提升使得纳米孪晶铜在IC制造应用成为可能,很大程度上促进了下一代互连材料的发展。

关键词: 脉冲电镀, 纳米孪晶铜, 盲孔填充, 大马士革工艺

Abstract:

High density nanotwinned copper films were pulse electroplated using an optimized electrolyte. In order to find out the influencing factors on the formation of nanotwins, series contents of MPS were added to the electrolyte during the pulse electroplating process. It was found that the copper films electroplated without MPS had large grains but a few nanotwins. And the grain size was about 0.9 μm on average, and the texture components of (110) and (111) crystal orientations were calculated as 49% and 27.8%, respectively. Differently, when 10 ppm MPS was added, the microstructure was changed to columnar grain with high density of horizontal nanotwins and the crystal orientation was also changed to highly (111) orientated one. However, when the MPS content was continuously increased from 10 ppm to 40 ppm, the microstructure and crystal orientation were almost unchanged as detected by the secondary ion microscopy of focus ion beam and X ray diffraction. Specifically, when 40 ppm MPS was used, the average grain size was 0.6 μm, and the texture components of (110) and (111) crystal orientations were 3.45% and 95.1%, respectively. It demonstrated that the nanotwinned copper can be electroplated at a large concentration range of MPS, which also meant that the filling ability of nanotwinned copper electrolyte could be adjusted by MPS content without influencing the microstructure. Finally, these electrolytes with different contents of MPS were used in the Damascene via filling. The results showed that when the content of MPS was 40 ppm, the Damascus via was completely filled without voids. The achievement of via filling with nanotwinned copper makes the application of nanotwinned copper possible in Integrated Circuit (IC) fabrication, which also greatly promotes the development of interconnected material for next generation.

Key words: pulse electroplating, nanotwinned copper, via filling, Damascene process